Here’s a closer look to the resin parts that come with the kit:

First up: Wash these parts in warm, soapy water to get rid of any mold release agent that might still be sticking to them. You need to get it off completely because it can prevent primer and paint from adhering to the surface properly.

Parts cast in resin are most times rough when they come out of the mold and have to be sanded smooth before processed further. In this case, the pouring of the resin created a ridge in the “walls” of the body shell. This is the area that will later be glued together. Here’s a close-up:

In order to make it possible to glue the parts together, you have to sand those areas smooth. I use a large piece of sandpaper mounted on a board to accomplish this.

The parts that come with the kit have already been pre-sanded, but you’ll still have to do some fine-tuning to fit the parts together perfectly.

Be careful not to sand too much material away – keep in mind that the electronics have to fit inside! Keep measuring the thickness of the two shells aligned to each other with a Caliper to make sure the prop will be equally thick on each corner.

Here’s the result:

Before continuing with the body, let’s pay some attention to the inner workings of the scanner first! Here are the electronics that are included in the kit:

Since the LEDs alone are not wide enough when placed next to each other, use some 1.0 mm styrene to act as spacers between them. This way, the width will be more accurate to the original prop.

This step can be quite tricky! Use some fast setting super glue and rough up the LEDs as well as the styrene with sandpaper or a file. When done, the glue will bond easier to the material.

Update: Since I wrote this tutorial, I’ve improved the set of electronics and am now using a LED bar instead of five seperate LEDs. Thereby the aforementioned (very elaborate) step in construction can be dropped:

Also, I am now using other super-bright red LEDs as the one shown here.

Next you’ll have to cut out all the windows out of the resin parts. Let’s start with the one for the front LEDs. As you can see in Part II, I specifically designed the silicone mold to create a particularly thin layer of resin in this area. That way this step is easily done with a sharp X-Acto knife.

Although the area of thin resin is fairly large, be sure not to create a window that is too big, because you wouldn’t want to have any gaps later. Keep comparing your assembled LED bar with the window to ensure a tight fit. Of course, if you want a bigger window, feel free to do whatever you think looks best. Gaps can be filled with putty later if needed.

Use a small jewelers file to smooth the edges. If necessary, use some spot putty to resculpt any imperfections here. Primer the part to reveal any blemishes and keep working until they are removed. When the electronics are installed, any work on this window will be very difficult, so complete it before the installation!

Next you need to cut out the battery door. The best place for it is in the handle on the backside of the prop. The opening can be conveniently hidden under one of the styrene parts that will be added later.

To determine the dimensions of the opening, simply measure the battery holder which is included with the kit. Then, cut out the matching styrene part using the included templates and place it on the handle.

Hint: Use spray glue to attach the templates to the styrene before cutting. This way the shape will be accurate and the paper can be easily removed in warm water.

Trace the outline of the detail piece and add the measurements of the battery holder like this:

The resin in the handle is approximately 5 mm thick, so you’ll need something more effective than an X-Acto knife this time. You can get good results if you drill four holes in the corners of the layout and then use a fretsaw to cut out the door.

This is the result.

Use a small and flat file to clean the shape of the door.

Now, the openings for both the trigger and the top LED have to be drilled. When doing that, it’s important to align the resin halves perfectly and to be careful not to bring them out of alignment during the drilling process.

For the trigger, simply drill a hole of 4 mm in diameter in the middle of the recessed area on the handle. Test fit the trigger and extend the orifice if necessary before continuing!

To determine the location of the opening for the top LED, use the template of the head piece, which will be added later. You can also use this and other pictures in this tutorial as a reference.

You’ll have to make sure that the electronic components have enough room inside the body to perform their function. To do this, you’ll need to dremel some of the material away.

This is where the battery holder will be put. You’ll have to align it to the door in the other body half, which will be placed on top of this one to enable easy access to the batteries. Again, use the dremel to create some more room if necessary.

This is how the electronics are arranged inside the prop:

To attach all of the components permanently into the resin shell, use a strong putty, for example a 2-component polyester putty which I use in my builds.

As you can see, all of the LED components are placed very near to each another. In case of the green running lights, this is on purpose and not a problem. But as far as the super-bright red LED is concerned, there is a problem with the close proximity to the green LEDs: Light bleeding. To make sure that the red LED doesn’t light up the green ones next to it when activated, you’ll have to putty up the entire area around the green LEDs and use black masking tape around the red LED.

When inserting the LEDs into the window, be sure not to make them flush with the front of the resin body. There needs to be some space for a piece of the included translucent plastic to go in there later.

When the electronics have been successfully installed and tested, the resin body can be permanently sealed. First, use 5 minute epoxy glue to attach the resin body halves to each other. Then, putty up the seam lines and sand them smooth when the putty has dried.

This is the most elaborate part of the buildup. Use primer to reveal any blemishes in the finish and remove them with spot putty and sandpaper until they’re all gone. Be sure to mask all LEDs and the trigger to protect them from sanding, puttying and priming!

Next, the head piece needs to be attached. Before you do that, sand a good portion of the top array off so that it will have the original thickness afterwards when the styrene is in place. Use the templates to cut out the shape and then use 5-minute epoxy to glue it on.

Again, putty the edges and use sandpaper to round them. Try to make it look as if the part was integrated into the overall shape of the prop from the beginning. As before, repeat the puttying, sanding and priming until the result is acceptable.

When everything is done, it’s time to paint!

You don’t want to glue the greeblies onto the paint later, so mask off all areas which will be enhanced with details. Then, paint the entire body with PK 7173 or a matching equivalent.

Don’t forget to drill the holes for the battery door screws!

When the paint has fully dried, mask off everything but the handle and the top scanner array and paint them with PK 7179 or a matching equivalent.

After this is done, remove the masking tape and continue with the last step.

Here all of the detail parts at a glance. For the emitter, shorten the acrylic rod to a length of approximately 12 mm and cut it in half. Sand the flat side of it to achieve a frosted look and a light diffusion effect.

Here are the color codes for the greeblies: Handle details, front ribbed piece and one of the small top details: copper metallic. The other small top detail: red. Rim strips and pointed front detail: PK 7179 or matching equivalent. Square additional detail on pointed front piece: beige. If you want, you can also paint the screws in the same color as the handle details to blend them in.

Again, use 5-minute epoxy or CA glue to attach the greeblies.

Screw the battery door in place after inserting two AAA batteries.

Fit the translucent plastic into the front LED window and insert it.

Cut out the display graphics that you wish to use and test fit them. When your display graphic fits the recess perfectly, use some thin double-sided adhesive tape to glue it inside. You can also use spray glue for this.

That’s it, your ODN Scanner is finished!

Now, go ahead and scan away!

The kit consists of the resin cast body and some tape which is added in the end. And that’s all there is to it, really.

Here are some detail shots of the casting:

And here is a picture of the original for comparison:

When I first tried to cast this prop up, I had a lot of trouble with air bubbles in my castings. Then I learned how to improve my technique of mixing the two resin components by adding them together and then pouring them from one cup to another several times instead of stirring them. So, very few air bubbles were left to be filled.

To fill the bigger holes I used a two-component polyester putty which is normally used in the automotive sector. It cures very quickly (within 30 minutes) and can be sanded very easily.

Here are two of the biggest bubbles already filled:

Next is sanding. This is the most elaborate step in any prop building project. You will spend a lot of time grinding and sanding. So, sandpaper is essential here.

Remember to “go through the grits”. This means that you should start with a higher grit sandpaper to roughly shape the object and then move to lower grit numbers to make the surface smooth. Be careful not to remove too much material in the beginning, because it’s much easier to remove a little more instead of adding something.

In the next picture you can see that I used a high-grit sandpaper to process the larger air bubbles first. The hole is still visible. Also, there is still putty which doesn’t belong there.

The tip of the instrument is next: Here I also filled a smaller air bubble and sanded it smooth going from high to low grit numbers.

I decided to drill a hole into the tip, because that’s how it is on my original aluminum prop. Also, it adds a lot of authenticity.

Sandpaper is not only used to sand down any left over putty, it is also necessary to remove other flaws that resin castings might have, for example the seam line. It occurs along the body where the two mold halves meet and is inevitable. Certain professional casting techniques however can reduce the seam line to an extent where it’s almost not visible anymore.

Reality is, that you should inspect every square centimetre or even millimetre of your prop and process it with sandpaper or putty. Sometimes however, sandpaper is not the first choice, for example when it comes to fine details or structures. In this case you should have several different small files handy to handle that.

For bigger kits or larger areas you can also use power tools like a belt sander. But be careful: These tools don’t allow the same control over your work as a manual job does. Before you know it, your project could be ruined because you removed too much material or you slipped and damaged something. Also, the risk of injuring yourself is a lot higher, so take the appropriate steps to protect yourself!

Now, if you think that the prop surface is smooth and you repaired all of the defects, apply the splash-coat (a coat of primer) to reveal any previously invisible imperfections: scratches, blemishes, pinholes.

Allright, there’s still a lot to do here!

To remove such small defects, I use a spot putty. It’s not necessary to mix it from two components which makes it very easy to use right out of the tube. I chose to use a red spot putty because it’s easily visible during the application as well as during sanding. Since it will be painted over later anyway, it won’t affect the final finish.

Here you can see the areas covered with spot putty:

After I had applied spot putty to every visible scratch, pinhole etc., I then again used sandpaper to once more remove any excess putty by “going through the grits” until the beige color of the resin becomes barely visible again. However, don’t take off too much – you don’t want to change the overall shape of the prop.

This is how the result looked like:

Now, another coat of primer was in order. After it had dried, I again took a hard look at every part of the prop. Normally there are still pinholes etc. left after this “second splash-coat”.

This is repeated until the prop body is absolutely perfect. Of course, the term “perfect” depends on what the person who is building the prop is regarding acceptable. Me, I’m a perfectionist and I probably do this way too often. Remember: The final coat of paint doesn’t hide any defects, but makes them even more visible!

A very important aspect here is patience. It can be quite unnerving to apply another coat of primer only to discover that there are still scratches or pinholes left. However, once they are all repaired, you can tap yourself on the shoulder knowing that you did everything possible to make the prop perfect.

Now that the surface was completely flawless, I could apply the final coat of primer. One last checking look: Is there still a… No, thank god it’s just a shadow!

After the primer had completely dried, I moved on to the paint. I used a chrome paint containing real aluminum particles to create a highly realistic approximation. Silver spray paint is also suitable for this. A little trick helps to prevent ugly paint blobs: Place the can in warm water for ten minutes. The heated paint will then be dispersed a lot finer.

One precept of painting is to apply several thin coats and let them dry before applying the next instead of spraying one thick coat. It’s alright if the primer is still visible after the first coat! Be patient, even if you want to finish the prop soon. You don’t want to ruin it during the last step by causing “paint noses” occurring due to too much paint, do you?

Once the painting process was finished and the paint was dry (again, you should rather wait a little long than ruining the prop), I could add the greeblies which was the last step in this buildup.

In this case, the greeblies are nothing more than differently colored grip tape cut to shape and attached at the correct areas (see illustration).

The last step is to paint the tip golden. Of course, I had to mask off the rest of the prop to protect it. I used crepe tape for this because it can be removed easily. Anyway, to avoid any risk of damaging the base paint, I only masked a small area at the tip and wrapped a paper napkin around the rest of the prop.

The prop is finally finished! Here’s how the result looks like:

Here are some comparison shots I did with the original aluminum version which served as a master model here:

There’s almost no difference visible on the pictures. The chrome paint is not quite as shiny as the real aluminum, but that was to be expected. Unfortunately it also tends to get even duller when handled.

Anyway, I think the result is very good and satisfying.